Saberproject

Luke Skywalker ANH

If this is your first mod, we recommend taking a look at the modding help page.

Disassembly

1. First, remove the blade, end cap and battery holder.

2. Loosen the large screw opposite the clamp. The box can now be taken apart completely.

3. Now loosen the two long screws and nuts that hold the metal plate on the clamp together.

4. Then remove the black part that contains the switch. To do this, unscrew both screws.

5. Desolder the switch wires and push them through the hole in the shell into the hilt. They need to sit deep enough inside the saber that they don't get pinched when the chassis is pulled out.

6. Now remove the four gold pins and the two small metal plates with pliers.

7. Now carefully bend the metal plate that held the blade retention screw upward and slide it sideways over the round insert.

8. Pull out the two pins that held the plate with pliers. Remove both screws as well.

9. Next, carefully pry out the glass eye and loosen the screw underneath. Then take out the round insert.

10. Finally, loosen the slotted screw below the emitter. The whole chassis can now be slid out of the hilt.

11. To separate the chassis parts, tap the pins inward with a pin punch or a pointed object.

Blade disassembly

12. Remove the LED strip from the blade. To do this, tap both steel pins outward with a pin punch and pull off the blade holder.

13. Then tap the small steel pin in the blade inward with a pin punch, after which the LED strip mount can be removed.

Soldering

14. Cut the mount open on both sides and detach the LED strip with its wiring. The clash sensor sits on the LED strip. Now carefully desolder it; the connector with the wires can stay on the strip.

15. Carefully cut or pry open the housing containing the soundboard on both sides.

16. Cut the wires leading to the LED strip connector.

17. To make the work easier, it's a good idea to take the soundboard out of the chassis. To do this, loosen the two screws that fasten the board to the lower half of the chassis.

18. Now solder the wires. After a successful test, the lower part of the clash sensor with the wires should be potted in hot glue.

19. If you unscrewed the soundboard, fasten it again just like before. Now attach the upper half of the chassis to the lower one and join them with a bit of tape or glue.

20. Glue the LED onto the heatsink with thermal adhesive.

Working on the blade holder

21. Press the lens holder with the lens into a 25mm long aluminum tube (25mm outer diameter, 1.5mm wall thickness, sold by the meter at hardware stores). You may need to sand down the edges of the lens holder.

22. Now slide the aluminum tube with the lens and lens holder into its future position in the blade holder. Drill two opposite holes through the blade holder and the aluminum tube. Make sure the holes are positioned so that the parts aren't damaged and there's enough room for the lens and lens holder.

23. Now tap both holes with an M4 thread.

24. Now connect the aluminum tube and the blade holder with two M4 set screws. This prevents the aluminum tube, which serves as the rear seat for the blade, from slipping. You may need to grind down the set screws so they don't protrude so far into the tube that they push the heatsink with the LED to the side.

Assembly

25. Slide the tube into the blade holder and screw it in place.

26. Now glue the LED with the heatsink onto the lens holder in the aluminum tube.

27. Then slide the blade holder and the soundboard chassis together, making sure no wires get pinched.

28. Finally, slide all the internals back into the saber and reassemble it by following steps 1 to 11 in reverse order.

Saberproject
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.